banner-news1
REPAIR FAQ
Back

Sinotruk Chassis Grease Points: A Complete Walk-Around

Short answer: grease points on a Sinotruk are not a list to work through once — they are a route to work through in a fixed order, every service, with a set amount of grease at each point. The two things that go wrong are a missed point and an overfilled one: a dry joint wears out and squeaks, and an overfilled joint splits a seal or forces grease out of a boot. Count the points on your own chassis, mark them, and build the habit of counting them back again after you finish.

Greasing is the cheapest preventive maintenance on the truck and the easiest to do badly. A grease gun held on a nipple for two seconds delivers almost nothing; a gun held on a sealed joint delivers pressure that finds the weakest seal. The technique is a slow, deliberate pump at each point until fresh grease appears, and then stop.

QUICK DIAGNOSIS — where grease is missing
  1. 1Squeak over bumps, worse when loaded — dry spring or shackle bushes. Grease is the fix and a missed point is the cause.
  2. 2Vague steering with a knock — dry steering linkage or a worn idler. Grease first, then assess wear.
  3. 3Grease escaping from a boot or a seal — overfilled point, or a seal that has already failed. Clean it and find out which.
Technician under a truck chassis greasing a lubrication nipple with a grease gun

Under the chassis with a gun. The route matters more than the effort.

1. The route, and why order matters

  1. Work one area at a time and never jump around. Front axle, then steering, then driveline, then rear suspension, then the fifth wheel or the body. A fixed route is how you avoid missing a point at the back of the engine bay.
  2. Wipe the nipple before you couple the gun. Dirt pushed into a joint is worse than a little missing grease, and a dirty nipple also fails to accept grease.
  3. Pump slowly until fresh grease appears, then stop. Fresh grease at the joint proves the passage is open and the joint is full. Continuing after that only stresses the seal.
  4. Check that the grease actually went in. A nipple that will not accept grease is blocked or the joint is full of old hardened grease, and that joint needs to be stripped and cleaned, not pumped harder.
Front axle steering knuckle and ball joint grease nipples with old grease visible on a truck

Knuckle and ball joint nipples. Front axle points take the most load and are missed most often.

2. The points that get missed

Area Points commonly missed Consequence
Front axle Inner knuckle, upper and lower kingpin or ball joint Heavy steering, wear, and a shimmy that is blamed on the tyres
Steering Idler arm, drag link ends, steering box input if fitted with a nipple Vague steering, wander, uneven tyre wear
Driveline Universal joints, centre bearing, slip joint Vibration and joint failure, often at speed
Rear suspension Spring eyes, shackle pins, torque rod ends Clunks, axle misalignment, accelerated spring wear
Fifth wheel or body Slider rails, pivot pins, tipper linkage Seizure, and a mechanism that stops working smoothly
Never grease a brake component or a wheel bearing through a nipple meant for something else. Grease in a brake drum or on a friction surface is a safety failure, and over-greasing a sealed bearing destroys the seal. Confirm what each nipple serves before you couple the gun.
Spring eye and shackle grease nipple on a truck being greased with a gun coupler

Spring and shackle points. These take load every bump and dry out fastest.

3. How much and how often

Frequency follows duty, not the calendar. A truck on un-made roads and in water needs greasing far more often than a highway tractor, because water washes grease out and dust absorbs what remains. The practical rule is to grease at every service interval and after any submersion, and to inspect the joints at the same time. As for quantity, the joint tells you: fresh grease at the exit point means full, and no fresh grease means the passage is blocked or the joint is dry inside, which needs investigation rather than more pressure.

4. Questions drivers ask most

Does more grease mean better protection?
No. Beyond the point where fresh grease appears, extra grease only loads the seal. The protection comes from the right grease being present, not from quantity.
Can I use one grease for everything?
Only if it meets every specification on the chassis. Some applications require a specific base soap, and mixing incompatible greases can leave a joint with neither.
Why will one nipple not take grease?
The nipple is blocked, the passage is blocked, or the joint is full of hardened old grease. Replace the nipple first, then strip the joint if it still refuses.
Does greasing hide a worn joint?
It can, briefly. A joint with play still has play when greased, so check for movement while you are under there — greasing is the moment to inspect, not to cover up.
Need grease nipples, universal joints, spring bushes, shackle pins or steering linkage parts for your Sinotruk truck? Send the chassis number and we will confirm the correct parts. Send your request

Grease specifications, nipple locations and service intervals differ by chassis and body. Confirm the lubrication chart in the OEM manual for your own truck.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4