banner-news1
REPAIR FAQ
Back

Sinotruk Urea Concentration and Dilution: What the System Detects

Short answer: The SCR system is calibrated for a defined urea concentration, and it detects when the solution is outside that range. Water added to the tank, a contaminated drum or the wrong product produces efficiency and reagent quality faults that are easy to mistake for a failed catalyst or a failing pump. A refractometer test on a sample from the tank settles the question in a minute and costs almost nothing.

Dilution lowers the ammonia available for the reaction, so the catalyst cannot convert the NOx it should and the efficiency monitor reports a fault. The system may also detect the concentration directly through its quality monitoring.

Contamination is a different problem: oil, diesel or soap in the tank damages the pump and poisons the catalyst, and no amount of correction of concentration will fix that.

QUICK DIAGNOSIS — solution or component?
  1. 1Efficiency fault shortly after a refill — Diluted or wrong product. Test the solution.
  2. 2Quality or concentration fault — Solution outside specification, test and replace.
  3. 3Pump and filter contaminated with oil — Contamination, drain and flush the system.
  4. 4Efficiency fault with correct solution and dosing — Catalyst or sensor, not the solution.
Urea sample taken from a truck tank being tested with a refractometer on a workshop bench

A refractometer test takes a minute. It separates a solution fault from a catalyst fault before any part is ordered.

1. Test the solution first

Take a sample from the tank, not from a drum, and test it with a refractometer calibrated for urea. Compare the reading with the specification for the product you are using.

Also look at the sample: a clear blue-green solution is normal, and any oil film, cloudiness or sediment means contamination rather than dilution.

  1. Take the sample from the tank after the truck has stood. A sample from the tank reflects what the pump sees.
  2. Test with a refractometer and record the value. Write the value down; it is evidence for the supplier conversation.
  3. Inspect the sample for oil, cloudiness or particles. Contamination is a different repair from dilution.
  4. If contaminated, drain and flush the system. Do not simply top up with fresh solution.

2. What each fault means

Dilution is a solution problem and the fix is to drain and refill with the correct product. Contamination is a system problem: the pump, filter and lines may need cleaning and the catalyst may already be damaged.

A genuine catalyst failure produces efficiency faults with correct solution, correct dosing and a healthy sensor. Prove the first three before ordering a catalyst.

Test result Meaning Action
Concentration below spec Diluted solution Drain and refill
Concentration above spec Wrong product or evaporation Drain and refill
Oil film or sediment Contamination Flush the system, inspect the catalyst
Concentration correct, dosing correct Catalyst or sensor Efficiency test, then decide
Urea sample in a clear container showing oil film and sediment from a contaminated tank

Oil film means contamination, not dilution. That repair includes flushing the system and inspecting the catalyst.

3. Storage and refilling practice

Store urea in a sealed original container, out of sunlight and away from freezing, and never transfer it into an unmarked container that could be mistaken for water. Most contamination events start with an unlabelled drum.

Keep the tank cap and the filler clean, and do not refill from a container that has held anything else. A single litre of diesel in a full tank is enough to produce a fault.

Never add water to urea to extend the range. Dilution is detected, it lowers conversion and it may poison the catalyst, which is a far more expensive outcome than the reagent saved.
Urea tank filler cap and clean filler neck on a truck during a refill from a sealed container

Sealed container, clean filler, no transfer into unmarked drums. Most contamination starts with an unlabelled can.

Questions drivers ask most

Can I use agricultural grade urea?
No. Use the product specified for SCR systems. Other grades contain contaminants that damage the catalyst.
Does cold weather affect urea?
It freezes at around minus eleven degrees. Systems have thawing strategies, and a tank that is frozen solid will produce faults until it thaws.
How much dilution triggers a fault?
That depends on the system’s monitoring. Even modest dilution raises NOx and can trip efficiency monitoring.
Is a refractometer expensive?
It costs less than one dosing valve and it answers the most common SCR question in a minute.
Need urea pumps, filters, dosing valves or SCR catalysts? Send the model and system number and we will confirm. Send your request

Urea specification and monitoring thresholds are system specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4