banner-news1
REPAIR FAQ
Back

Sinotruk Urea Pump Pressure Low: Prime, Filter and Diaphragm

Short answer: The SCR system needs a defined urea pressure at the dosing valve, and when the pump cannot build it the system logs a pressure fault and stops dosing. The truck then derates. Nearly every low pressure complaint resolves to one of three causes: air in the supply because the tank was run dry or the suction line leaks, a blocked filter at the pump, or a worn diaphragm. Test pressure before replacing the pump.

Urea is not diesel. It is a water based solution that crystallises when it dries, and it destroys a pump that is left uncirculated for long periods. Sitting over a season is as damaging as a dirty supply.

The pressure fault symptoms are consistent: a countdown on the dash before the torque limit, a pressure code, and often a pump noise that is different from usual.

QUICK DIAGNOSIS — pressure fault?
  1. 1Countdown and torque limit after refilling from empty — Air in the supply. Prime the system.
  2. 2Pump runs, no pressure, filter wet with crystals — Blocked pump filter. Clean or replace.
  3. 3Pressure builds then drops with each dose — Diaphragm or internal leak in the pump.
  4. 4Pressure fine when cold, fails when hot — Worn pump or a suction leak that opens with heat.
Urea dosing pump and filter assembly mounted on a Sinotruk truck with supply line to the dosing valve

Prime, filter and diaphragm cover most low pressure faults. The pump itself is rarely the first suspect.

1. Prime and check the filter

After the tank has been run dry, or after any work on the supply line, the system must be primed with the diagnostic routine. A pump that is trying to compress air will not reach pressure however healthy it is.

Then remove the pump filter and inspect it. White crystal deposits on the mesh mean the filter is blocked, and the pump is working against a restriction rather than failing.

  1. Check the tank level and the quality of the solution. Diluted or contaminated urea produces pressure and quality faults.
  2. Run the priming routine and watch the pressure value. Pressure that rises steady is healthy.
  3. Remove and inspect the pump filter for crystals. Crystals are visible and the filter is cheap.
  4. Check the suction line for air leaks and loose joints. Air in the line shows as pressure that will not hold.

2. The diaphragm and the module

A pump that primes and then loses pressure with each dose has an internal leak, usually the diaphragm or a check valve. On most current modules the repair is a replacement of the pump unit rather than a repair in the field.

Check the pressure at the dosing valve as well as at the pump. A restriction or a leaking valve downstream produces the same code, and the pump is blamed for a fault that is two metres away.

Symptom Cause Action
Pressure zero after refill Air in the line Prime the system
Pressure rises then falls Diaphragm or check valve Replace the pump
Pressure at pump but not at valve Downstream restriction or leak Check lines and valve
Crystals at the filter Dried urea Clean or replace filter
Urea pump filter removed showing white crystal deposits blocking the mesh

White crystals on the mesh are dried urea. This is a filter, not a pump, and it is a fraction of the cost.

3. Behaviour that prevents the fault

Do not run the tank below the reserve level if the truck is going to stand for weeks, and do not leave the system without a dosing cycle for long periods. A short drive that triggers dosing keeps the lines clear.

Store urea in a sealed container out of sunlight, and never top up with water. Dilution is detected by the quality sensor and produces its own fault.

Never clean a urea pump or line with diesel, solvent or soap. Residues contaminate the solution and the catalyst, and the resulting repair is far more expensive than the pump.
Urea supply line and dosing valve connection on a truck with correct joint condition

Check pressure at the valve as well as the pump. A leak two metres downstream produces the same code.

Questions drivers ask most

Can I drive with a urea pressure fault?
The system will derate the engine after its countdown. Driving to a workshop is possible within the countdown, but not a full day’s work.
Does the pump need replacing when the filter blocks?
No. Clean or replace the filter and prime the system, then re-check the pressure.
Why does the fault appear after refilling?
Because air entered the supply. The priming routine is the fix, not a new pump.
Is tap water acceptable for dilution?
No. Urea must be used as supplied, and dilution is detected. Only distilled water is acceptable for cleaning, never for mixing.
Need urea pumps, filters, dosing valves or SCR modules? Send the model and the system number and we will confirm. Send your request

Urea pressure values and module part numbers are system specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4