banner-news1
REPAIR FAQ
Back

Sinotruk Injector Sleeve Leak: Coolant in the Cylinder and Hard Start

Short answer: The injector sits in a thin sleeve that separates it from the coolant jacket, and when that sleeve seal fails, coolant drips into the cylinder overnight. The symptoms copy a head gasket exactly: white steam at start-up that clears, a hard cold start, coolant loss with no external leak. The difference is where the coolant comes from, and it is found by pressurising the jacket with the injectors removed.

A sleeve leak is small and slow. It fills the piston bowl while the truck stands, and the first compression stroke pushes water into the exhaust as steam. By the time the driver notices, the coolant level has usually been topped up three or four times.

The cheapest way to avoid a head job you did not need is to look into the injector bores before the head comes off.

QUICK DIAGNOSIS — sleeve or gasket?
  1. 1Coolant in the injector bore, sleeve wet below the tip — Sleeve seal. Reseal the sleeve, no head removal needed on most builds.
  2. 2Coolant loss plus bubbles in the reservoir under load — Often the head gasket, because gas is entering the jacket.
  3. 3Hard cold start with white steam that clears in a minute — Coolant in a cylinder, from sleeve or gasket, confirmed by pressure test.
  4. 4Coolant in the oil, no steam at all — Oil cooler or a porous casting, not the sleeve.
Injector bore in a Sinotruk cylinder head after the injector has been removed, showing the sleeve and copper washer seat

The bore is where the answer is. A wet sleeve below the tip with a dry head face points at the sleeve seal.

1. Pressure the jacket with the injectors out

Remove the injectors and their copper washers, then pressurise the cooling system cold and watch each bore for a rise of coolant. A bore that fills slowly is the leaking sleeve. A bore that stays dry while the gauge falls means the leak is elsewhere, and the next candidates are the head gasket and the oil cooler.

Take the reading with the engine cold and with the cooling system filled to the normal level, because a low system will not show a slow leak within the test window.

  1. Remove all injectors, keeping each one labelled by cylinder. Injection quantity and trim data are cylinder specific on some builds.
  2. Clean and dry every bore before the test. Residual coolant from removal will look like a leak.
  3. Pressurise the jacket and watch the bores for five minutes. A slow rise is enough; do not wait for a stream.
  4. Inspect the copper washer seat for combustion gas erosion. A blackened seat means gas was escaping past the injector, a different fault.

2. Resealing the sleeve

The sleeve is sealed at the top by an O-ring or a pressed joint, depending on the build, and at the bottom by the copper washer under the injector. A sleeve that has been leaking for a while usually has a corroded seat, and a new seal on a corroded seat leaks again.

Drain the coolant below the sleeve level, clean the bore, fit the new seal with the correct lubricant, and torque the injector to the specified value with a new copper washer. Reusing a copper washer that has been through two heat cycles is the most common reason a reseal does not hold.

Evidence Meaning Action
Bore fills under pressure, head face dry Sleeve seal failure Reseal the sleeve, new copper washer
Bore dry, gauge falls, bubbles in reservoir Head gasket gas path Gasket job, deck flatness check
Copper washer seat blackened and eroded Combustion gas past the injector Reseat the bore, new washer, check torque
Coolant grey and oily, no steam Oil circuit involved Oil cooler and cooler seals
Cooling system pressure tester connected with injectors removed from a diesel cylinder head while bores are watched

Injectors out, jacket pressurised, bores watched. This is the test that decides between a sleeve and a gasket.

3. After the repair

Refill with the correct coolant mix, run the engine to temperature with the cap on, and check the level after it cools. A level that falls again after a reseal means the repair did not hold or there is a second leak path.

Change the oil if coolant reached the sump, because coolant and oil form an emulsion that does not separate and will not lubricate. A flush is cheaper than the bearing damage it prevents.

Do not start an engine that has coolant sitting in a cylinder. Liquid does not compress, and a hydraulic lock bends a connecting rod before the starter stall is noticed.
New injector copper washer and sleeve seal being fitted into a cleaned injector bore of a truck diesel head

A new copper washer every time. A reused washer is the most common reason a reseal fails within weeks.

Questions drivers ask most

Can a sleeve leak be repaired without removing the head?
On most Sinotruk builds yes, because the sleeve is accessible from the top with the injector out. Confirm the procedure for your cylinder head in the manual.
Why does the truck only smoke when cold?
Because the coolant accumulates while the engine is stopped. Once it is pushed out as steam during the first minute, the cylinder runs normally.
Does a sleeve leak affect injector life?
Yes. Coolant and steam at the injector tip accelerate nozzle corrosion, and a leaking sleeve often ends with a replacement injector.
Will a pressure test find a very small leak?
Usually, if the system is held at the rated pressure for several minutes with the bores clean and dry. A leak too small to see still shows as a slow rise.
Need injector sleeves, copper washers, O-rings or replacement injectors? Send the engine and cylinder head numbers and we will confirm the correct parts. Send your request

Sleeve designs, seal part numbers and injector torque values are build specific. Confirm them in the OEM manual before starting the job.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4