banner-news1
REPAIR FAQ
Back

Sinotruk Driveshaft Centre Support and Universal Joint Service

Short answer: Long wheelbase trucks run a two piece driveshaft with a centre support bearing and a universal joint at each end. The support bearing carries the shaft, absorbs misalignment and isolates vibration. When it wears, the shaft runs out of line and vibration appears at a specific road speed, often accompanied by a clunk on torque reversal.

Universal joints wear too, and a dry or seized joint produces a cyclic vibration that changes with load rather than with speed alone.

Both parts are inexpensive and both are frequently misdiagnosed as axle or gearbox faults because the vibration is felt through the whole chassis.

QUICK DIAGNOSIS — where is the vibration?
  1. 1Vibration at one road speed band — Driveshaft balance or centre support.
  2. 2Clunk when torque reverses — Universal joint play or worn support.
  3. 3Vibration worse under load — Joint seizure or support bearing collapse.
  4. 4Grease missing at a joint — Dry joint, immediate replacement needed.
Two piece truck driveshaft with centre support bearing mounted on the chassis frame

The centre support carries the shaft and isolates vibration. When it wears, the vibration appears at a specific road speed.

1. Locate the vibration

Note the road speed band where the vibration appears and whether it changes with load. A pure speed related vibration suggests balance or support, while a load related one suggests joints.

Then inspect the centre support: cracked rubber, a bearing that turns with play, or a bracket that has moved are all visible with the truck on a lift.

  1. Note the speed band and the load dependence. This separates balance from joint faults.
  2. Inspect the centre support rubber and bearing. Cracks and movement are visible on a lift.
  3. Check every universal joint for play and grease. A dry joint is a pending failure.
  4. Confirm the shaft phasing and the joint angles. Wrong phasing produces a constant vibration.

2. Joints, phasing and angles

Universal joints must be phased so their oscillations cancel. A shaft reassembled one spline out of phase vibrates at all speeds.

Joint angles also matter: a lifted or modified suspension changes the angles and produces vibration that no balance will fix.

Symptom Cause Action
Vibration at one speed band Balance or support Balance shaft, replace support
Clunk on torque reversal Joint play Replace joint
Vibration after a repair Phasing or angle Re-phase, check angles
Squeak at low speed Dry joint Grease or replace
Universal joint with worn needle bearings and missing grease on a truck driveshaft

A dry, worn joint shows up as a clunk on torque reversal. Grease it at every service or replace it.

3. Service and verify

Grease the joints at every service with the correct grease, and replace any joint that has lost its grease or shows play. Replace the centre support as an assembly rather than only the bearing, because the rubber is usually as worn as the bearing.

Then road test through the speed band where the vibration appeared and confirm it is gone under load and on overrun.

Never ignore a dry universal joint. When it seizes at speed the shaft can fail completely, and a detached driveshaft is dangerous.
New centre support bearing and universal joints fitted on a truck driveshaft before a road test

New support and joints, correct phasing, correct angles. Then verify in the speed band where the vibration was.

Questions drivers ask most

Can I replace only the support bearing?
Possible, but the rubber is usually worn too. The assembly is the reliable repair.
Why does vibration appear only at 60 to 70 km/h?
That is the resonant band of the shaft. Balance and support problems concentrate there.
How often should joints be greased?
At every service interval, and more often in wet or dusty work.
Does a lifted suspension cause vibration?
Yes. It changes joint angles, and the resulting vibration is not a balance fault.
Need centre support bearings, universal joints or complete driveshafts? Send the model and wheelbase and we will confirm. Send your request

Joint part numbers and phasing procedures are model specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4