banner-news1
REPAIR FAQ
Back

Sinotruk Final Drive Backlash and Contact Pattern Adjustment

Short answer: The crown wheel and pinion in a final drive must mesh with a specific backlash and a contact pattern that sits in the correct part of the tooth face. Both are set with shims, and both must be correct together: a pattern that looks acceptable with the wrong backlash will still whine, and a backlash that measures correctly with the pattern in the wrong place will wear out in a few thousand kilometres.

The complaint after a rebuild is a whine on drive or on overrun, and the cause is almost always one of the two settings, or a pinion depth that was never checked.

The procedure needs marking compound, a dial gauge and patience. It is not a job that can be done by feel.

QUICK DIAGNOSIS — what the whine tells you
  1. 1Whine on drive, quiet on overrun — Pattern too close to the toe or depth wrong.
  2. 2Whine on overrun, quiet on drive — Pattern too close to the heel.
  3. 3Whine at all speeds, loudest at one — Backlash out of specification.
  4. 4Noise with a hot axle only — Oil grade or quantity, or an overtight preload.
Final drive crown wheel and pinion being set up with marking compound on a truck axle

Backlash and contact pattern must be correct together. A rebuild set by feel always whines.

1. Measure backlash first, then read the pattern

Measure backlash at several points around the crown wheel and confirm it is within specification and consistent. A variation around the wheel means a distorted or incorrectly seated crown wheel.

Then apply marking compound and turn the pinion under load in both directions. Read the pattern on the drive and coast sides of the tooth.

  1. Measure backlash at four points around the crown wheel. Consistency proves the wheel is seated correctly.
  2. Apply compound and load the gears in both directions. You need both drive and coast patterns.
  3. Read the pattern position on the tooth face. Depth and shim adjustments follow from this.
  4. Adjust pinion depth shims, then backlash, and repeat. One change at a time, re-read after each.

2. Preload, oil and break-in

Carrier bearing preload and pinion preload both affect the pattern and the noise, so set them before the final pattern check. Overtight preload produces heat and noise that no pattern adjustment will remove.

After assembly, use the specified oil, fill to the correct level and follow a break-in procedure with a load check and a temperature check after the first run.

Symptom Cause Action
Whine on drive Pattern near the toe Move pattern toward the heel
Whine on overrun Pattern near the heel Move pattern toward the toe
Noise hot only Preload or oil Check preload and oil
Backlash varies Crown wheel not seated Re-seat and re-measure
Contact pattern on a crown wheel tooth face after marking compound test

The pattern tells you which way to move the pinion. Read it before changing any shim.

3. Verify with a loaded run

After reassembly, run the truck loaded for a short distance, then check the axle temperature and listen for noise. A correct setup runs cool and quiet.

Check the oil for metal after the first few hundred kilometres. Fine particles are normal during break-in; flakes are not.

Never set a final drive by sound alone. A whine that is accepted as normal becomes a destroyed crown wheel and pinion within a short distance.
Axle temperature checked with an infrared thermometer after a loaded test run

A correct setup runs cool. Temperature after a loaded run is the cheapest proof you have.

Questions drivers ask most

Can I reuse the old shims?
Only if the measurements say so. Reusing them assumes nothing changed, and something always did.
How long should break-in take?
Follow the OEM schedule, and check oil and temperature after the first loaded run.
Does the oil grade matter?
Yes. The wrong grade changes film strength and produces noise and wear.
Why does it whine only when hot?
Thermal expansion changes backlash and preload, which points at an incorrect initial setting.
Need crown wheel and pinion sets, shim kits or final drive bearings? Send the axle model and we will confirm. Send your request

Backlash and preload values are axle specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4