banner-news1
REPAIR FAQ
Back

Sinotruk Four Circuit Protection Valve: One Circuit Dead

Short answer: The four circuit protection valve splits compressed air into separate circuits, front service brake, rear service brake, parking brake and auxiliary, so a failure in one does not empty the others. When one circuit loses pressure while the rest hold, the fault is usually inside the valve: a stuck piston, a failed seal or a spring that has lost tension.

The symptom is specific and easy to confirm: one circuit gauge stays at zero, or the circuit only builds when another is drained.

Testing per circuit at the valve ports is the fastest way to prove it, and it prevents replacing good valves downstream.

QUICK DIAGNOSIS — one circuit dead
  1. 1One circuit zero, others normal — Protection valve piston or seal.
  2. 2Circuit builds only when another is drained — Internal cross leakage in the valve.
  3. 3All circuits low — Supply or compressor, not the valve.
  4. 4Circuit drops overnight — Leak downstream, or the valve passing
Four circuit protection valve with its four delivery ports on a heavy truck air system

One circuit at zero with the others holding points at the valve, not at the components downstream.

1. Test each port

Connect a gauge to each delivery port and build pressure. A port that stays at zero while the supply is good has an internal fault in the valve.

Then close the circuit downstream and see whether the valve then holds. A valve that only holds against a closed circuit and not against an open one is passing internally.

  1. Confirm supply pressure at the inlet port. No supply is a compressor fault.
  2. Read pressure at each of the four delivery ports. One dead port is the valve.
  3. Isolate each circuit and re-check. Separates valve faults from downstream leaks.
  4. Check for cross leakage between circuits. A circuit that fills from another means internal leakage.

2. Internal parts and contamination

The valve contains pistons and springs that close a circuit when pressure drops. Contamination, oil from the compressor or ice in winter jams them, and the circuit stays closed even when supply is restored.

Replacing the valve without fixing oil carryover or a wet system means the new valve fails the same way.

Test result Meaning Action
One port zero, supply good Valve internal fault Replace or repair the valve
Circuit fills from another Cross leakage Replace the valve
All ports low Supply fault Check compressor and governor
Port good, circuit still dead Downstream restriction Check lines and components
Four circuit protection valve removed and opened showing pistons and springs inside

Pistons and springs close a circuit on pressure loss. Contamination and oil jam them closed.

3. Protect the repair

Before fitting a new valve, service the air dryer and drain the reservoirs, because oil and water are what destroy these valves.

After fitting, build pressure and confirm all four circuits reach their correct values, then leak test with the engine off.

Never plug or bypass a circuit on a four circuit valve to keep a truck working. The remaining circuits lose their protection and a single failure can take out the service brake.
All four air circuits checked at their gauges after protection valve replacement

All four circuits at their correct values, then a leak test with the engine off.

Questions drivers ask most

Can one circuit fail without warning?
Yes. The valve protects the others, so the driver may only notice one gauge.
Is the valve repairable?
Some are, with a kit. Most fleets replace it because a mis-assembled valve is worse than a new one.
Does oil in the system destroy the valve?
Yes. Compressor carryover is the most common cause of repeat failures.
Why does the circuit only build when I drain another?
Internal cross leakage, which means the valve must be replaced.
Need four circuit protection valves, repair kits or air dryers? Send the model and we will confirm. Send your request

Circuit pressures and valve part numbers are model specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4