banner-news1
REPAIR FAQ
Back

HOWO TX MAX Driveshaft Vibration: Joints, Balance and Support

Short answer: driveline vibration on a HOWO TX MAX has three usual owners and one rule: check the cheap ones first. A vibration that starts under acceleration and disappears when you lift off is a universal joint or a worn spline. A vibration that is present at a fixed road speed regardless of load is balance. A vibration that appears only at high speed with a droning noise is shaft phasing or a centre support that has sagged. None of these are found by replacing a propeller shaft on suspicion — measure the joint play, the run-out and the support height.

Multi-axle tippers and mixers run long drivelines with a centre support bearing and a two-piece shaft. Every one of those joints has to be in phase with the next, or the shaft will fight itself and produce a vibration you cannot balance away. That phasing check is the one most often skipped.

QUICK DIAGNOSIS — when the vibration happens
  1. 1Under acceleration, worse in a low gear, gone when coasting — universal joint, spline wear or a loose centre support.
  2. 2At a fixed road speed, in any gear, either accelerating or coasting — balance or run-out of the shaft itself.
  3. 3High speed only, with a low drone through the floor — phasing between the two shaft sections, or a support bearing rubber that has collapsed.
Driveshaft centre section and support bearing on a HOWO TX MAX chassis photographed underneath the truck

Centre support and its bearing. A collapsed rubber here lets the shaft orbit instead of spin true.

1. Start with the joints, they are free to check

  1. Chock the wheels, release the parking brake, and lock the driveline. Any play you find has to be found with the shaft unloaded, otherwise the torque holds the joint tight and hides the wear.
  2. Twist each joint by hand. A universal joint should have almost no rotational play. Any visible slop, or a joint that moves before the shaft does, is a worn joint — and a dry joint that has lost its grease will seize and then crack the yoke.
  3. Feel for a notch. Rotate the joint slowly through its range. A joint that binds at one point in rotation is a joint with a brinelled bearing, and brinelling produces a vibration at exactly twice shaft speed.
  4. Check the slip spline. Push and pull the shaft axially where the spline allows. Play here appears as a clunk on take-off and a vibration under load, because the shaft length is changing faster than the spline can follow smoothly.
Universal joint and grease nipple on the driveshaft of a HOWO TX MAX with old grease visible at the joint

A dry joint with old grease packed at the edge. Grease must reach the bearing, not just the fitting.

2. Phasing and balance, in that order

A two-piece shaft has to be assembled so that the yoke of the front joint and the yoke of the rear joint sit in the same plane. If a shaft has been apart and reassembled one spline out, the two halves are out of phase and the result is a vibration that no balance shop can correct. Mark the yokes before disassembly, and check them against each other if a vibration started right after a repair.

Balance comes after phasing. Look for a missing balance weight, a dented shaft, or a shaft that has been run with a wrap of tape or a cable tie left on it. A shaft that is bent from an impact will show run-out when you spin it against a fixed pointer with the wheels off the ground.

Symptom Most likely cause Test
Clunk on take-off, vibration under load Slip spline play or a loose centre support Push-pull the shaft; check support mounting bolts
Vibration at 2× shaft speed Universal joint brinelling Rotate the joint by hand and feel for a notch
Vibration independent of gear and load Balance or run-out Dial gauge on the shaft with wheels raised
Drone through the floor at high speed Phasing, or collapsed support rubber Compare yoke planes; inspect the support bush
Vibration plus a rumble that changes with steering Not the driveline — wheel bearing Jack the wheel and spin it free of the driveline
Never run a truck with a joint that has been “topped up” and left dry inside. A dry joint does not vibrate — it seizes, and a seized joint at road speed twists the yoke until it cracks. If grease will not go in through the nipple, the bearing is blocked and the joint is finished.
Balance weight on a HOWO TX MAX driveshaft with a witness mark showing where a weight has shifted

A balance weight that has moved or gone missing turns a smooth shaft into a shaker at one particular speed.

3. What a worn centre support does to everything else

The centre support holds the shaft in a straight line between two joints. When its rubber collapses, the shaft is allowed to orbit, and the resulting vibration loads the transmission output bearing, the axle pinion seal and both universal joints. That is why a truck with a collapsed support often arrives with three complaints at once — a drone, a leaking pinion seal and a rumble — and why replacing only the seal guarantees the leak comes back.

4. Questions drivers ask most

Can I drive with a vibrating driveline?
Short distances at reduced speed only, and only if the joints are tight. A vibration that is a balance fault is uncomfortable; a vibration that is a worn joint is a shaft that can let go.
Does a new propeller shaft need balancing?
A shaft supplied as a balanced assembly does not. A shaft that has been re-tubed, straightened or had a yoke replaced does need checking, and the phasing must be set before it goes back in.
How often should the joints be greased?
At every chassis lubrication interval, with grease that actually reaches the bearing. A joint that takes grease every service but never shows grease at the seal is not being lubricated.
Why does the vibration get worse with a full load?
Load increases the torque through the joints and lowers the ride height, which changes the shaft angle. A joint that is marginal when empty can be clearly worn when loaded.
Need universal joints, slip yokes, centre support bearings or a complete propeller shaft for your TX MAX? Send the shaft length and joint size and we will confirm the assembly. Send your request

Shaft lengths, joint sizes and phasing marks are specific to the wheelbase and axle configuration. Confirm the assembly details in the OEM parts catalogue before replacing driveline components.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4