banner-news1
REPAIR FAQ
Back

HOWO TX MAX Wiper and Washer Faults: Motor, Linkage and Nozzle

Short answer: a wiper that stops mid-screen on a Sinotruk truck is usually a linkage that has come off its ball joint, or a motor that has lost its park circuit — not a fuse. The fuse test tells you quickly: if the fuse is intact and the motor is silent, look at the linkage; if the motor runs and the blades do not move, the linkage has disconnected; if the motor runs and parks in the wrong place, the park switch or the earth is at fault. Never force a jammed linkage with the motor, because the arm can bend and the screen will be scratched.

Wipers are a safety system, not a comfort feature. A wiper that parks in the middle of the screen, or a washer that does not spray, takes the driver’s attention away at exactly the moment the road needs it. The diagnosis is simple and the repair is usually cheap, provided you stop using the motor as a diagnostic tool.

QUICK DIAGNOSIS — where the fault is
  1. 1Motor silent, fuse intact, no click — switch, relay or motor. Test for voltage at the motor plug while the switch is on.
  2. 2Motor runs, blades do not move — linkage off its ball joint, or a stripped spindle.
  3. 3Blades stop in random positions, motor still running — park switch or earth, so the motor cannot find its rest position.
Wiper arm and worn wiper blade on the windscreen of a Sinotruk truck cab

Arm and blade. A blade this worn also streaks, which drivers mistake for a linkage fault.

1. The linkage, and why it fails

  1. Open the cowl panel and look at the linkage. On most cabs the mechanism sits under the panel at the base of the screen. Look for a rod that has come off a ball cup, and check each cup for cracking.
  2. Move the arms by hand with the motor disconnected. The mechanism should move through its full sweep freely. Stiffness means a seized spindle bush, and a stiff linkage is what pulls the rod off the cup in the first place.
  3. Check the spindle bushes for water. Water sitting in the cowl rusts the bushes and the linkage, and that is why the failure is so common on trucks that work in rain.
  4. Refit with new cups and clips, and grease the joints. A rod pressed back onto a worn cup comes off again, and the second time it usually happens in traffic.
Windscreen washer reservoir and electric washer pump connector in the engine bay of a Sinotruk truck

Washer bottle and pump. A pump that hums with no spray has a blocked jet or a split hose.

2. Washer faults, in order of frequency

Symptom Cause Fix
Pump silent Fuse, switch or pump seized Test voltage at the pump plug with the switch pressed
Pump runs, nothing sprays Blocked jet, split hose, or empty bottle with a leaking seal Clear the jet with a pin from the outside, check the hose
Sprays weakly on one side Partly blocked jet or a hose with a kink Clean the jet; replace a kinked hose
Water appears inside the cab Split hose or a disconnected jet body Find the leak at the nozzle; a wet fuse box follows if ignored
Never leave a jammed linkage powered. If a blade is stuck under snow or ice and the motor is switched on, the motor will bend the arm or strip the spindle. Clear the screen by hand before switching the wipers on in freezing weather, and use the correct winter washer fluid rather than water.
Wiper linkage mechanism under the cowl panel of a truck cab with rust visible at the spindle bushes

Linkage under the cowl. Rusted spindle bushes are what break the rod off its cup.

3. Blades, and the reason wipers get blamed unfairly

A worn blade leaves streaks and unwiped patches, and drivers report it as “the wipers do not work”. A blade that has hardened in the sun cannot conform to a curved screen, and no adjustment of the arm will fix it. Blades are a consumable and should be changed on condition, not on a calendar; in a dusty market that can be far more often than the service book suggests. Check the arm spring as well — a weak spring lifts the blade at speed, and the streak pattern then moves with road speed.

4. Questions drivers ask most

Why do the wipers stop in the middle of the screen?
The motor has lost its park signal, either through the park switch inside the motor or through a bad earth. The blades then stop wherever the motor happened to be when power was removed.
Can I use plain water in the washer bottle?
In warm weather it works but leaves deposits that block the jets, and in cold weather it freezes and splits the bottle. Use washer fluid mixed to the correct concentration for the climate.
Why does only one wiper work?
Almost always a linkage rod off its cup on that side, or a stripped spindle. Both are visible once the cowl panel is open, and both are cheap to repair.
Is it safe to drive with one wiper?
No. The remaining blade sweeps a smaller area and the broken side often scores the screen. Fix the linkage rather than driving on it.
Need wiper motors, linkage assemblies, arms, blades or washer pumps for your Sinotruk cab? Send the chassis number and cab type and we will confirm the correct parts. Send your request

Wiper linkage layout, motor type and blade lengths vary by cab. Confirm them in the OEM parts list for your chassis before ordering.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4