banner-news1
REPAIR FAQ
Back

Sinotruk Caster and Camber Checks on a Loaded Truck

Short answer: Caster is the tilt of the kingpin that makes the steering self-centre, and camber is the tilt of the wheel that keeps the tyre flat on the road under load. Both change when the truck is loaded and when the suspension settles, so a measurement taken on an empty truck at the wrong ride height can be inside specification while the truck still pulls or wears tyres.

The symptoms are specific: poor self-centring and a heavy feel at speed point at caster, while one shoulder wearing and a pull to one side point at camber.

Measure with the truck in its working condition and on a level floor, and check for bent components before adjusting anything.

QUICK DIAGNOSIS — caster or camber
  1. 1Steering does not self-centre well — Caster low or unequal side to side.
  2. 2Truck pulls to one side — Camber or caster difference between sides.
  3. 3One shoulder of a tyre wears — Camber on that wheel.
  4. 4Wear appears only when loaded — Geometry changes with load. Measure loaded.
Front wheel of a loaded heavy truck measured for camber and caster with alignment gauges

Loaded and on a level floor. Caster and camber change with ride height, so the condition matters.

1. Measure in the working condition

Load the truck as it normally runs, or at least at the load the complaint occurs with, and check ride height is correct before measuring. A sagging suspension changes both angles.

Then measure caster and camber on both wheels and compare side to side. A difference between sides is more informative than an absolute value slightly outside the range.

  1. Check ride height and suspension condition. Sag changes both angles.
  2. Measure caster and camber on both front wheels. Compare side to side.
  3. Compare with the specification at that load. Values shift with load.
  4. Inspect the axle and steering arms for damage. Bent parts change the angles.

2. What changes the angles

Worn spring bushes, a bent axle beam, a collapsed kingpin bearing and incorrect shimming at the axle all change caster and camber. So does a suspension repair that changed ride height without re-checking alignment.

On most truck axles camber is not adjustable; it is restored by replacing the worn or bent part. Caster is adjusted with shims on some axles.

Finding Cause Action
Caster low on one side Bent axle or worn bush Repair the component
Camber out both sides equally Worn kingpin bearing Replace bearing
Angles change after a repair Ride height changed Re-align to the new height
Pull with correct angles Brake or tyre fault Check brakes and tyres
Front axle beam and kingpin area inspected for a bent component on a truck

Most camber faults are a bent or worn component, not an adjustment. Find it before measuring again.

3. Verify after the repair

After replacing a component, re-measure at the working load and road test for self-centring and pull. A repair that corrects the number but not the feel is not finished.

Then watch the tyres for the next few thousand kilometres, because wear is the final proof.

Never bend or shim an axle to correct camber on a loaded truck. The measurement is the symptom; the worn or bent component is the cause.
Front tyre tread inspected for even wear after alignment correction on a heavy truck

Even wear across the tread after a few thousand kilometres is the proof that the geometry is right.

Questions drivers ask most

Can camber be adjusted on a truck axle?
On most axles no. It is restored by replacing worn or bent parts.
Why measure loaded?
Load changes ride height and both angles. An empty measurement can hide the fault.
Does caster affect tyre wear?
Indirectly, through steering feel and scrub. Camber wear is more direct.
How often should alignment be checked?
After any front end work, impact or suspension repair.
Need axle beams, kingpin kits, spring bushes or shims? Send the model and we will confirm the parts. Send your request

Caster and camber values at load are model specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4