banner-news1
REPAIR FAQ
Back

Sinotruk Engine Mount Failure: Vibration, Fan Contact and Clutch Judder

Short answer: Engine mounts fail slowly and their symptoms are blamed on everything else. A collapsed front mount lets the fan tip touch the shroud on a hard stop. A failed rear mount shows as driveline vibration at idle and a judder when the clutch takes up. The test is a pry bar and a jack, five minutes, engine off, and it tells you which of the three mounts has lost its rubber.

On a heavy truck the engine sits on two front mounts and a transmission mount or a rear crossmember. The rubber in each one carries load, damps vibration and limits movement. When it perishes, the engine moves further than it was designed to, and the parts around it pay the bill.

Drivers rarely describe it as a mount problem. They report a vibration, a noise when braking, or a clutch that grabs.

QUICK DIAGNOSIS — which mount?
  1. 1Vibration at idle that disappears when the engine is revved — Front mount collapsed or its bolt loose.
  2. 2Fan blade touching the shroud on a hard stop or a bump — Front mount movement. Stop using the truck until checked.
  3. 3Clutch judder on take-off, worse with a load — Rear or transmission mount allowing the driveline to twist.
  4. 4Clunk on acceleration and deceleration — Mount bolt or a worn rubber, confirmed by a pry bar test.
Technician using a pry bar to check engine mount movement on a Sinotruk diesel engine

A pry bar shows movement that a visual inspection misses. Engine off, wheels chocked, hands clear of the fan.

1. The pry bar test

Engine off and cold, place a pry bar between the mount bracket and the frame and lever gently. A mount that is still serviceable will resist and return. A collapsed mount moves easily and stays where you put it, because the rubber has separated from the steel or the bonded centre has torn.

Check all three mounting points, and check the bolts as well as the rubber. A loose bolt produces the same clunk as a failed mount and costs nothing to tighten.

  1. Check the front mounts with a pry bar, one at a time. Watch the gap between the rubber and the steel plate.
  2. Check the rear or transmission mount from below with a jack and a block of wood. Lift only enough to see movement, never enough to lift the frame.
  3. Inspect the fan-to-shroud clearance with the engine off. Any witness mark on a blade means the engine has moved under load.
  4. Look for a cracked bracket rather than a failed rubber. A cracked bracket is a weld repair, not a part swap.

2. Why mounts fail early

Heat, oil and overload are the three killers. A mount that sits under an exhaust leak cooks its rubber; one that is washed by an oil leak from the front cover swells and perishes; one that is loaded beyond its rating after a front axle or suspension change fails within months.

Wrong installation is the fourth. A mount fitted with the engine hanging on it, rather than with the engine supported in its designed position, is pre-loaded from the first kilometre.

Symptom Mount involved Confirms as
Idle vibration, gone at speed Front left or right Rubber collapsed or bolt loose
Fan contact on braking Front mount Excess fore-aft movement
Clutch judder under load Rear mount Driveline twist beyond limit
Clunk on throttle change Any mount Bolt, rubber or a cracked bracket
Vibration worse after a repair New mount installed pre-loaded Refit with the engine supported
Worn rubber engine mount with cracked bonded rubber beside a new mount on a truck workshop bench

A separated bonded rubber is visible once the mount is off. The pry bar test finds it while it is still fitted.

3. Replacing without creating a new fault

Support the engine on a jack with a block under the sump, never on the oil pan drain plug, and replace mounts one at a time. Fit the bolts loosely, lower the engine into its natural position, then tighten in the specified order. Tightening a mount with the engine hanging on it pre-loads the rubber and shortens its life.

After replacement, check the fan clearance, the exhaust joint alignment and the wiring harness to the engine. A mount that has been collapsed for months usually has a chafed harness or a strained pipe somewhere.

Never run an engine with a fan that has touched the shroud. A blade that has cracked will let go at speed, and the damage moves from the radiator to the cab.
Fan blade with a witness mark close to the shroud on a truck engine, showing mount movement

A witness mark on a blade is a mount symptom, not a fan fault. Check the mount before replacing the fan.

Questions drivers ask most

Can I drive with a collapsed engine mount?
Only to a workshop at low speed and without hard braking. Fan contact and driveline misalignment get expensive quickly.
Do mounts need replacing in pairs?
Replace both front mounts together if one has failed, because the second one has carried the extra load and is close behind.
What causes a mount to fail repeatedly?
Oil or heat exposure, a misaligned bracket, a cracked frame at the mounting point, or a mount fitted pre-loaded.
Is vibration at idle always a mount?
No. Injector balance, dual mass flywheel wear and driveline joints all produce idle vibration. Test the mounts first because it is the cheapest check.
Need engine mounts, brackets or mounting bolts for your Sinotruk? Send the model and the mounting position and we will confirm the correct part. Send your request

Mount part numbers and tightening sequences are model specific. Confirm them in the OEM manual before replacing.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4