banner-news1
REPAIR FAQ
Back

Sinotruk Hub Reduction Axle: Oil Transfer and Bearing Checks

Short answer: A hub reduction axle carries a planetary gear set in each wheel hub, which means each wheel end has its own oil level and its own bearings. Oil moves between the hub and the axle through a transfer path, and when that path is blocked or the hub is filled to the wrong level, the planetary set runs dry while the differential still shows a healthy level.

The failure mode is quiet: the hub gears and bearings wear without any warning until a wheel end becomes noisy or a bearing collapses.

Checking the hub level at every service is the whole prevention, and it takes a few minutes per wheel.

QUICK DIAGNOSIS — hub or main oil?
  1. 1Hub noisy but differential level correct — Hub running dry. Check level and transfer path.
  2. 2Oil leaking at the hub only — Hub seal or overfilled hub.
  3. 3Magnetic plug at hub full of metal — Bearing or planetary wear, hub is failing.
  4. 4Hub hot after a run — Wrong oil level or bearing preload.
Hub reduction wheel end with planetary gear set exposed on a heavy truck axle

Each wheel end has its own oil level. Correct main axle oil tells you nothing about the hub.

1. Check the hub level, not just the axle

Each hub has a level plug at a defined position. Remove it and confirm oil is at the plug with the wheel in the correct rotational position. A dry hub with a full differential is the classic sign of a blocked transfer path.

Then check the hub magnetic plug. A little fine fuzz is normal; flakes or a metallic paste mean the bearing or planetary set is failing.

  1. Position the wheel so the level plug is at the correct height. Position matters for an accurate check.
  2. Remove the plug and confirm oil at the plug. A dry hub is a transfer or fill fault.
  3. Inspect the hub magnetic plug for metal. Flakes mean the wheel end is failing.
  4. Check the transfer path between hub and axle. A blocked path starves the hub.

2. Bearing and planetary checks

With the hub removed, inspect the planetary gears, the sun gear and the bearings. Wear shows as pitting on the gear teeth and discolouration on the bearing races.

End play and preload are set with shims and must be measured. A hub that is set too tight runs hot, and one set too loose produces noise and seal leaks.

Finding Meaning Action
Hub dry, axle full Transfer path blocked Clear the path, refill
Metal flakes at hub plug Bearing or gear wear Overhaul the wheel end
Hub hot after a run Preload or oil level Re-set and refill
Oil at hub seal only Overfilled hub or worn seal Correct level, replace seal
Hub reduction planetary gears and bearings inspected on a workbench during a wheel end overhaul

Pitting and discolouration are the evidence. Measure end play rather than judging by feel.

3. Service routine that prevents failures

At every service: check the hub level, check the magnetic plug, and confirm the transfer path is open. At every oil change: use the correct oil for the hub and the axle, and do not substitute a single grade for both unless the manual allows it.

After an overhaul, run the truck loaded and check hub temperature by hand or with an infrared thermometer. A wheel end that is noticeably hotter than its neighbour has a problem.

Never top up a hub through the axle and assume the oil reached the wheel end. Fill each compartment at its own plug.
Hub oil level check at the level plug with the wheel in the correct position

The wheel position matters. Check the level at the plug with the wheel rotated to the correct point.

Questions drivers ask most

How often should hub oil be checked?
At every service, and after any water crossing or long idle period.
Can I use the same oil in hub and axle?
Only if the manual specifies it. Some axles use different grades.
Why does only one hub run hot?
Preload, bearing condition or a blocked transfer path on that side.
Is a magnetic plug necessary?
It is the cheapest early warning available. Check it every time.
Need hub reduction gears, bearings, seals or wheel end kits? Send the axle model and we will confirm. Send your request

Oil grades, levels and preload values are axle specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4