banner-news1
REPAIR FAQ
Back

Sinotruk Relay and Quick Release Valve: Slow Brake Release

Short answer: On an air braked truck, the relay valve supplies air to the brake chambers when the foot valve commands it, and the quick release valve exhausts the air when the command stops. When release takes several seconds, the driver feels dragging brakes, the drums run hot, and the fault is almost always in one of those two valves rather than in the foot valve.

The complaint is specific: brakes apply normally, but the truck seems to drag or the gauge takes a long time to fall after release.

A per axle release test identifies the valve in minutes, which prevents replacing a good foot valve.

QUICK DIAGNOSIS — slow release
  1. 1Release slow on one axle only — Its relay or quick release valve.
  2. 2Release slow on all axles — Foot valve or supply restriction.
  3. 3Dragging with hot drums — Restricted exhaust at a quick release valve.
  4. 4Release normal cold, slow when hot — Seal or valve clearance changing.
Relay valve and quick release valve mounted on a truck chassis near the rear axle

Relay valve applies, quick release valve exhausts. Slow release is almost always one of the two.

1. Release time per axle

Apply full brake and note the time the brake chambers take to exhaust when the pedal is released, one axle at a time. A healthy system releases in about a second, and any axle that takes noticeably longer has the fault.

Then listen at the quick release valve: a clear, unrestricted exhaust is what you should hear.

  1. Apply full brake and hold. Then release and time the exhaust.
  2. Compare each axle. One slow axle localises the valve.
  3. Listen at the quick release valve for a free exhaust. A muffled hiss means restriction or mud.
  4. Check the relay valve for a sticking spool. Sticking keeps air applied.

2. Common causes

Mud, ice, oil from the compressor and worn seals all restrict the exhaust path. On winter trucks, ice in the quick release valve is a common cause of dragging brakes until the truck warms up.

A relay valve whose spool sticks leaves the brakes partially applied, which heats the drums and destroys the linings inside a day.

Symptom Suspect Action
One axle slow to release Relay or quick release valve Clean or replace
All axles slow Foot valve Test and replace
Dragging after a winter start Ice in the valve Dry the system, service the dryer
Hissing continues after release Leaking valve or line Locate with soap solution
Quick release valve with mud and debris around its exhaust port on a truck chassis

An obstructed exhaust port keeps air in the chambers. The drums then run hot and the linings wear out.

3. Verify and protect

After cleaning or replacing the valve, repeat the per axle release test and confirm all axles exhaust together. Then check brake chamber pressures are balanced.

Service the air dryer and drain the reservoirs, because the same contamination will return otherwise.

Never ignore dragging brakes because they still stop the truck. Heat from dragging destroys linings, drums and seals, and can start a fire on a long descent.
Brake chamber release time checked after valve replacement on a truck rear axle

All axles should exhaust together. Balanced release is the proof that the valve repair worked.

Questions drivers ask most

How fast should brakes release?
Around a second on a healthy system. Slow release is measurable and comparable between axles.
Can I clean a quick release valve?
Usually yes, if it is contamination rather than wear. Replace it if the seal is damaged.
Why do brakes drag only in winter?
Ice forms in the exhaust path. Service the dryer and drain the tanks daily in freezing weather.
Does a slow release affect fuel economy?
Yes, dragging brakes cost fuel and destroy components.
Need relay valves, quick release valves, brake chambers or air dryers? Send the model and we will confirm. Send your request

Valve part numbers and release times are model specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4