banner-news1
REPAIR FAQ
Back

Sinotruk Steering Box Play and Recirculating Ball Adjustment

Short answer: A recirculating ball steering box has one adjustment that most workshops reach for too early: the sector shaft adjusting screw. Turning it in reduces play at the steering wheel, and if the play was actually coming from the linkage, the box ends up preloaded and the steering becomes heavy or self-centring fails.

The correct sequence is to measure play at three points: the steering wheel, the linkage and the box input. That separates a worn linkage from a worn box in about twenty minutes.

Only after the linkage is proven good should the box be adjusted, and only to the specification, with the wheels straight ahead.

QUICK DIAGNOSIS — where the play is
  1. 1Play at the wheel, none at the linkage — Steering box wear or adjustment.
  2. 2Play at the linkage with the wheel held — Worn joints, kingpins or the drag link.
  3. 3Steering heavy after adjustment — Box over-tightened. Back it off and re-check.
  4. 4Wheel does not self-centre — Box preload too high or the sector is worn.
Recirculating ball steering box fitted to a heavy truck chassis with its adjustment screw visible

One adjustment screw, and it is not the fix for every play complaint. Measure the linkage first.

1. Split the play into three measurements

With the front wheels straight and the engine off, measure free play at the steering wheel rim. Then hold the wheel still and check each linkage joint for movement with a helper or a bar.

Finally measure at the box input shaft while watching the pitman arm. Movement at the input without movement at the output is play inside the box.

  1. Measure free play at the steering wheel rim. Record it against the specification.
  2. Hold the wheel and check every joint for play. Linkage play is the most common cause.
  3. Watch the box input versus the pitman arm. Play inside the box shows here.
  4. Check the steering shaft and its universal joint. A worn UJ feels like box play.

2. Adjust only what is worn

If the play is inside the box, adjust the sector screw to the specification with the wheels straight ahead, then re-check the free play and confirm the steering self-centres on a road test.

If the linkage is worn, replace the joints. Adjusting the box to compensate for linkage wear produces a truck that is heavy in the centre and vague at the ends of the travel.

Measurement Result Action
Wheel play high, joints tight Box play Adjust to specification
Joint play with the wheel held Linkage wear Replace joints
Input moves, output does not Internal box wear Adjust or overhaul
Heavy after adjustment Over-tightened Back off and re-check
Steering linkage joints checked for play with a bar while the steering wheel is held

Hold the wheel, pry the joints. Play shows instantly and it is usually not the box.

3. Verify on the road

After any adjustment, drive the truck and confirm the steering returns to centre after a turn, does not wander at speed and is not heavy at parking speeds.

A box that is adjusted and then overheats or leaks at the sector seal has been over-tightened, and the seal is the first casualty.

Never adjust a steering box to remove play you have not located. Over-tightening wears the sector and pinion and can make the steering fail to return, which is dangerous.
Road test of a truck checking that the steering self centres after a turn

Self-centring and feel after a turn is the proof. A number on the gauge is not enough.

Questions drivers ask most

Can play be adjusted out completely?
No. A worn box has a limit, and beyond it the box must be overhauled or replaced.
Why is my steering heavy after a workshop visit?
The box was adjusted for linkage play. Have it backed off and the linkage repaired.
Does a worn steering UJ feel like box play?
Yes. Check the shaft and joint before touching the box.
How often should play be checked?
At every service, and immediately if the driver reports wandering.
Need steering boxes, pitman arms, drag links or steering shaft joints? Send the model and we will confirm. Send your request

Free play limits and adjustment procedures are model specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4