banner-news1
REPAIR FAQ
Back

Sinotruk Wheel Bearing Preload: Setting It Without Guesswork

Short answer: Wheel end bearings are the most loaded bearings on the truck, and they are the ones most often set by tradition rather than measurement. Tapered roller bearings want a small preload or a defined end play, depending on the axle design, and hub reduction axles add a second bearing set with its own requirement.

Too tight produces heat, discoloured grease and a bearing that fails on a long run. Too loose produces wheel shake, uneven tyre wear and a seal that leaks.

Both failures are silent until they are expensive, which is why the measurement matters.

QUICK DIAGNOSIS — tight or loose
  1. 1Hub hot after a run — Preload too high or grease wrong.
  2. 2Wheel shake and uneven tyre wear — End play too large.
  3. 3Grease discoloured, bearing blue — Overheated from excessive preload.
  4. 4Seal leaking at the hub — Loose bearing allowing shaft movement.
Wheel hub bearing and adjusting nut being set with a torque wrench on a truck axle

Preload is a measured value. Feel is how bearings end up either hot or loose.

1. Know the bearing type and method

Tapered roller bearings are usually set with a defined end play or with a specified torque and then backed off by a stated amount. Unitised bearings have their own procedure, and hub reduction axles add a planetary set that affects the setting.

Follow the method for the axle, not the method used on another truck. Mixing methods is how a bearing gets preloaded twice.

  1. Identify the bearing type and the specified method. Tapered, unitised or hub reduction.
  2. Clean and inspect the bearing and the bore. Never set a bearing with debris inside.
  3. Pack with the correct grease and quantity. Over-packing also causes heat.
  4. Measure end play or torque as specified. Measurement, not feel.

2. Temperature and grease

A hub that is noticeably warmer than its neighbour after a loaded run has a preload or grease problem. Check with an infrared thermometer rather than by hand on a hot day.

Grease quantity matters in both directions: too little starves the bearing and too much churns and overheats.

Symptom Cause Action
Hub hot, bearing blue Preload too high Re-set to specification
Wheel shake End play too large Re-set and check the spindle
Seal leak Loose bearing Re-set, replace seal
Even heat, normal Correct setting Continue scheduled checks
Wheel bearing packed with grease and inspected for discolouration before assembly

Blue or discoloured rollers mean the last setting was too tight. Inspect before reusing.

3. Check after the first run

After a bearing service, run the truck loaded for a short distance and check hub temperature on both sides. That single check catches most setting errors before they become failures.

Then check again after a few hundred kilometres and confirm the seal is dry.

Never spin a wheel to listen for bearing noise and call it good. Noise is a late symptom; temperature and play are the early ones.
Hub temperature measured with an infrared thermometer after a loaded test run

Compare both sides after a loaded run. A hot hub is a setting error, not a coincidence.

Questions drivers ask most

Can I set bearings by feel?
No. The correct value is measured, and feel varies between people.
How much grease should a hub take?
The specified quantity for that axle. Too much overheats as well.
Why is one hub hotter?
Preload, grease quantity or bearing condition on that side.
Do unitised bearings need packing?
Usually not. Follow the axle procedure.
Need wheel bearings, seals, spindles or hub nuts? Send the axle model and we will confirm the correct set. Send your request

Preload and end play values are axle specific. Confirm them in the OEM manual.

Need Help or Want More Detailed Maintenance Information?

Please contact our team for personalized maintenance guidance and technical support for your Sinotruk HOWO, A7, or T7 trucks. We provide professional advice and recommendations for genuine parts to help ensure the reliable operation of your fleet.

Contact Us
More Articles

Howo Sinotruk Parts & Catalog PDF

Whenever your truck needs repair, you don’t know how to buy the right parts?

Don’t worry, we have already done this job for you. We have a complete parts list catalog for different models of each truck assembly, you can choose the right catalog to download and collect according to your truck configuration.

When you have a need, you can send us your required list based on this catalog.

Obtain the complete Howo truck parts catalog PDF file and pricing.

Contact Us

Hot-Selling Replacement Parts

whatsapp-4